materiale : copper
for Thor Soft Hammers
Made in Great Britain
Φ 25 mm
gross weight : 90 g
*1: La faccia del martello deve essere sostituita prima di danneggiare la testa. Per prima cosa, assicuratevi che la maniglia non sia danneggiata. Se è danneggiato, deve essere sostituito con uno dei seguenti la dimensione, la forma e il tipo di manico corretti. Assicuratevi anche che la maniglia non sia allentata nella testa. Se la maniglia si è allentata, è necessario proteggerla nuovamente o sostituirla, se possibile.
*2: Tagliare e rimuovere il più possibile la vecchia faccia. Praticare un foro al centro della faccia, facendo attenzione a non forare la faccia. Rimuovere la maggior parte possibile della faccia usando un trapano da fondo o una fresatrice con un piatto.
*3: Si può essere in grado di afferrare il centro della vecchia superficie della pelle e piegarla verso l'interno in questo caso.
*4: Una volta rimossa la vecchia faccia, inserire la nuova faccia. Il cerchio deve essere aperto quel tanto che basta per inserire la nuova faccia. Il modo migliore per eseguire questa operazione è la combinazione di una pressa adeguata e di uno strumento di apertura/chiusura.
*5: Con la nuova faccia in posizione, invertire lo strumento di combinazione e chiuderlo intorno alla nuova faccia con la pressa appropriata. Anche in questo caso, il cerchio dovrebbe essere abbastanza chiuso da tenere la faccia saldamente in posizione. Quando è montato correttamente, il viso può essere ruotato.
*6: Molti clienti sostituiscono il lato pelle, ma il lato rame usato è particolarmente difficile da rimuovere. Le prese di rame hanno delle piccole scanalature che permettono al rame di diffondersi durante l'uso. Il rame che usiamo è puro al 99%, morbido, e può fungere da fungo sulla testa del martello dopo un uso considerevole. Una volta che la superficie si è trasformata, a seconda dell'applicazione, il rame durerà quasi indefinitamente in questo stato senza ulteriori deformazioni. Molti clienti trovano più economico usare l'estremità di rame per la rottura.
*Si prega di notare che le specifiche del prodotto possono essere soggette a modifiche a causa della convenienza del produttore. Per favore, cerca di capire.
Material: copper
for Thor Soft Hammers
Made in Great Britain
Φ 25 mm
Gross weight: 90 g
*1: The face must be replaced before any damage occurs to the hammer head.First, make sure that the handlebar is not damaged.If it is damaged, it should be replaced with one of the followingCorrect size, shape and type of handle.Also make sure the handlebar is not loose in the head.If the handlebar is loosened, it must be re-protected or replaced, if possible.
*2: Cut and remove as much of the old surface as possible.Drill a hole in the center of the face, taking care not to drill into the face.Use a bottom drill or milling machine to use the flats and remove as much of the face as possible.
*3: You may be able to grab the center of the old skin surface and fold it inward in that case.
*4: After the old side is removed, insert the new side.The rim must be opened just enough for the new surface to fit.The best way to perform this operation is a combination of a suitable press and an opening / closing tool.
*5: With the new face in place, reverse the combination tool and close it around the new face with a suitable press.Again, the rim is closed enough to hold the face firmly in place.When correctly mounted, the face can be rotated.
*6: Many customers replace the skin face, but the used copper face is particularly difficult to remove.Copper sockets have small grooves in them, and the copper will enlarge during use.The copper applied to the products is 99% pure, soft, and can mushroom on the hammerhead after considerable use.In this state, depending on the application, the copper lasts almost indefinitely without further deformation once the surface has been set.Many customers find it more economical to use the copper end for destruction.
*There may be changes in product specifications due to the manufacturer's reasons.