La nuova frizione assistita e antisaltellamento è leggera da impugnare, il freno motore è delicato e ben accolto..
Tuttavia, "il tocco è troppo dolce e troppo debole se usato con forza".. Siamo stati consultati su come gestire la situazione"..
La frizione è stata progettata per mantenere le migliori caratteristiche delle frizioni assistite e antisaltellamento, rafforzandole..
Questa parte sopprime le vibrazioni anomale della molla della frizione e migliora la precisione di funzionamento..
[Effetto]
Disinnesto dolce della frizione.
Rinforzato senza rondelle.. Si collega e si scollega saldamente senza scivolare..
Con le rondelle, anche con i pesi convenzionali, la sensazione di funzionamento è migliore rispetto al prodotto originale..
Sarà più facile farlo in anticipo!
Riduzione del judder.
Migliore durata dei dischi.
Come macchina, funziona più come un progetto..
Le molle sono progettate per essere meno soggette a vibrazioni..
Come vestirsi.
1. Scaricare il refrigerante e l'olio, scollegare il tubo del refrigerante, il tubo dell'olio e il cavo della frizione dal coperchio della frizione e rimuovere il coperchio..
2. Rimuovere i tre bulloni, il disco di regolazione, la molla e la frizione..
3. Inserire la molla con il fermo montato, applicare la piastra di regolazione e serrare i tre bulloni in dotazione.. I bulloni sono a gradini per evitare tintinnii..
4. Se non si vuole appesantire la presa dell'attuale leva della frizione (donne e persone con dita deboli), inserire i tre "bulloni in dotazione" nella piastra di regolazione, il fermo e le rondelle in dotazione e quindi serrarli contro la molla..
5. Senza rondelle, è rinforzato e un po' più pesante.. Una volta riempito, pesa praticamente come l'originale..
6. Verificare che il fermo si inserisca nella molla, quindi serrare gradualmente le tre barre di fermo, portandole a 12 Nm o meno (10 N sono sufficienti)..
7. Dopo l'installazione, dall'alto è visibile solo la differenza tra i bulloni.. Mi sono preso la briga di anodizzarlo in rosso..
8. Quindi, se la guarnizione è tagliata o strappata (le guarnizioni Honda sono più spesso danneggiate), rimuoverla con un raschietto, applicare una pietra abrasiva, inserire una nuova guarnizione e rimontare in ordine inverso..
Dischi della frizione
Nuovo e ben collegato. Il manuale mostra i limiti di utilizzo per lo spessore, ma questo non è utile..
Nel caso dei dischi di frizione di tipo sughero, se la superficie è lucida e croccante quando l'unghia viene premuta contro l'angolo, il disco è carbonizzato.. Non si collega come nuovo..
Come regola generale, il tipo di sughero ha raggiunto la fine della sua vita quando i grani di sughero sono diventati così neri da non poter essere distinti..
Ma se fai fatica in montagna o fai sempre impennate, anche un paio nuovo di zecca può durare un giorno!.
I mantenitori sono efficaci per migliorare il tocco e il disinnesto della frizione, ma "voglio ridurre maggiormente la resistenza aerodinamica".. Per evitare ulteriori perdite di calore.. La scanalatura e la smussatura del disco frizione sono efficaci..
The new assist and slipper clutch is light to grip, engine braking is gentle, and well received.
However, "the touch is too sweet and too weak when used hard.and consulted with them on how to handle the situation.
It was produced in the direction of strengthening while retaining the good points of the assist & slipper clutch.
■This part suppresses abnormal vibration from the clutch spring and improves the operating accuracy.
[effect]
・Smooth disengagement of the clutch.
・Reinforced without washers.The connection can be cut firmly without slipping.
・With washers, even with conventional weights, the feel of operation is better than stock.
・It will be easier to do up front!
・Judder reduction.
・Improved durability of the disc.
When installed, it works more like a machine designed to work.
The spring made it difficult to vibrate.
■Mounting Method
1. Drain the coolant and oil, disconnect the coolant hose, oil pipe and clutch wire from the clutch cover, and remove the cover.
2. Remove the three bolts, setting plate, spring, of the clutch.
3. Insert the spring with the retainer installed, apply the setting plate, and tighten the "three supplied bolts.The attached bolts are stepped to prevent rattling.
4. If you do not want to make the current clutch lever grip any heavier (for women or those with weak fingers), insert the three "supplied bolts" into the setting plate, then insert the retainer and supplied washers, and tighten them against the spring.
5. If you do not put in the washer, it will be reinforced and a little heavier.When filled, it weighs basically the same as the stock.
6. Check that the retainer fits into the spring, and then gradually tighten the three retainers, tightening them at 12 Nm or less (10 N is sufficient).
7. After installation, only the difference in the bolts can be seen from the top.I went to the trouble of anodizing it red.
8. Then, if the gasket is cut or torn (Honda is more likely to damage it), remove it with a scraper or similar tool, apply a grinding stone, insert a new gasket, and assemble in the reverse order.
■About clutch discs
The newer, the better the connection.The manual shows the limit of use of the thickness, but it is not helpful.
In the case of a cork type friction disc, if the surface is shiny and crispy when you put your fingernail on the corner, it is carbonized.Doesn't connect like a new one.
As a rule of thumb, the cork type has reached the end of its life when the grains of the cork become so black that they cannot be distinguished.
But if you struggle in the mountain or practice wheelie, even a brand-new bicycle may be worn out in a day.
■Retainers are effective in improving clutch touch and disengagement, but "I want to reduce drag more.To avoid more heat loss.Clutch plate grooving and chamfering is effective for the "clutch plate grooving and chamfering".